LM3429MHX/NOPB

Texas Instruments
926-LM3429MHX/NOPB
LM3429MHX/NOPB

制造商:

说明:
LED照明驱动器IC Simple N-channel con troller for constan A 926-LM3429MH/NOPB

ECAD模型:
下载免费库加载程序,将此文件转换,以供您的ECAD工具使用。了解详情。

供货情况

库存:
0

您可以延期订购此产品。

在途量:
5,000
预期 2026/3/6
5,000
预期 2026/3/23
生产周期:
6
大于所示数量的预计工厂生产时间。
最少: 1   倍数: 1
单价:
¥-.--
总价:
¥-.--
预估关税:
封装:
整卷卷轴(请按2500的倍数订购)

定价 (含13% 增值税)

数量 单价
总价
剪切带/MouseReel™
¥21.8316 ¥21.83
¥16.2946 ¥162.95
¥14.8934 ¥372.34
¥13.4018 ¥1,340.18
¥12.656 ¥3,164.00
¥12.1588 ¥6,079.40
¥11.8311 ¥11,831.10
整卷卷轴(请按2500的倍数订购)
¥11.3339 ¥28,334.75
¥11.0062 ¥55,031.00
† ¥15.00 MouseReel™费将被加上并在购物车计算。所有MouseReel™订单均不可撤消和退回。

备用包装

制造商零件编号:
包装:
Tube
供货情况:
库存量
单价:
¥22.9277
最小:
1

类似产品

Texas Instruments LM3429MH/NOPB
Texas Instruments
LED照明驱动器IC N-CHANNEL CONTROLLER A 926-LM3429MHX/NOP A 926-LM3429MHX/NOPB

产品属性 属性值 选择属性
Texas Instruments
产品种类: LED照明驱动器IC
RoHS:  
1 Output
Boost, Buck, SEPIC
5 A
HTSSOP-14
75 V
4.5 V
100 kHz to 2 MHz
Adjustable
LM3429
- 40 C
+ 125 C
Adjustable Switch Frequency, Enable/Shutdown, Thermal Shutdown
Reel
Cut Tape
MouseReel
商标: Texas Instruments
调光: Analog, PWM
输入电压: 4.5 V to 75 V
安装风格: SMD/SMT
通道数量: 1 Channel
产品类型: LED Lighting Drivers
工厂包装数量: 2500
子类别: Driver ICs
电源电流—最大值: 3 mA
单位重量: 52.400 mg
找到的产品:
要显示类似产品,至少选中一个复选框
要显示该类别下的类似产品,请至少选中上方的一个复选框。
已选择的属性: 0

此功能要求启用JavaScript。

CNHTS:
8542399000
CAHTS:
8542310000
USHTS:
8542310030
JPHTS:
854239099
TARIC:
8542399000
MXHTS:
8542399901
ECCN:
EAR99

IS32LT3175N/P Single-Channel Linear LED Drivers

ISSI IS32LT3175N/P Single-Channel Linear LED Drivers come with fade in/out and PWM dimming. The regulators serve as a stand-alone LED driver-configurable from 20mA to 150mA with external resistors, no microcontroller is necessary. A logic level “courtesy light” signal from the PWM pin can be interfaced to precisely drive the LED channel. The IS32LT3175P obtains a positive polarity PWM signal. In addition, the IS32LT3175N obtains a negative polarity PWM signal. The regulator integrates a 63-step fade-in and fades out the algorithm (Gamma correction). This causes the output LED current to increasingly rise up to the full source value after the EN pin is pulsed.